Equipment Breakdown Records

Hoisting lowering failure due to low oil pressure fault, Toped up Engine oil 10L. Engine start by ma ...

Hoisting lowering failure due to hoist position calibration out, Hoist position recalibrated

Control failure due to hybrid Battery 01 unit fault. Checked and craned parked for repair

Control failure, Trolley Joystick Zero signal missing,corected.

Control failure, Engine actuator fault, corrected manually and charged the battery.

Gantry travelling fault tracing/CMMS not functioning. Fault tracing on line

Hoisting lowering speed low due to spreader 40 signal missing fault failure

Wheel turn failure due to wheel o0 postion fault function operated again crect fault

Hoisting lowering failure due to Hoist drive A0042 shown, Checked the encoder connections and encode ...

Operator cabin seat repair due to cannot lock seat moving, fix the seat moving

Spreader function failure due to spreader 40 signal missing fault, Adjusted the spreader 40 (IN) sig ...

Operator cabin seat repair due to cannot lock seat moving, repaired the lock assembaly

Control failure due to e.room over temperate sensor mal function &Time to time stop, Bypassed E.room ...

travelling failure due to Right side anti collision time to time detect fault(No object), Anti colli ...

Control failure due to MEG not getting load time to time released fault, Cheked the Actuator functio ...

Control failure due to MEG not starting fault low SOC level, Reset and Manually stat engine/Up to SO ...

hydraulic oil leak due to anti-sway P#1 motor Horse mounting loosen, Tight the horse connection and ...

Control off due to spreader pump tripped because of overload, Breaker reset and released to operatio ...

Hoist function slow due to spreader 40' signal missing, Proximity adjusted.

Hoist function slow due to overload fault (Load cell fault due to P#2 loadcell signal not present) a ...

PLC Communication failure with SCS4, SCS4 restart

Drop cable came out of the HBK basket, Re-assembled the cable inside the HBK basket

Unlock fault due to Spreader LHS unlock solenoid coil wire burst and LHS unlock signal not presented ...

Unlock fault due to Spreader LHS unlock solenoid coil wire burst and LHS unlock signal not presented ...

Control ON failure due to MEG starting fault and low SOC level(Report starting signal not present). ...

Control failure (control off with a container) due to hoist truster brake supply contactor fault/ Tr ...

OHS 06 P#3 unlocked from spreader but not from OSH, Manually unlocked

LHS anticollision not working due to output contactor wire loose connection, Contactor wire connecti ...

Trolley traveling fault. P#2 trolley guide roller worn out, Lubricated the bearing ,need Replaced g ...

Control failure due to hoist drive over temperature fault - F23,Deive fan working condition; Drive r ...

Operator cabin A/C not working properly, Gas filled and released to operation.

Function failure due to Wheel pin lock signal missing - P#2,Manually turned on the wheel turn pump a ...

Controll off

Control failure. trolly vibration and trolly les activated and corrected.

Engine Stop (Gantry Fault). Leg #3 lock signal fail,manualy corrected

Control failure due to batterr room #01 BMU out of service,Replaced from RT22 but not correcte the f ...

Hoisting lowering failure due to 40' position signal missing,Adjusted the 40' proximity SR .

Hoisting lowering failure, Hoist rope touch with Emergency brake roof mounting post when lowering ( ...

Spreader Unlock Indication not work, Replaced indication light

Engine stop, Coolant low level 2L top up

Lock unlock fault Due to CAN moduler & P# 4 &5 lock solonid wire loosen in CAN modul on bellow the ...

Wheel turn failure due to wheel turn P03 90° not present,Manullay operated the wheel from local sta ...

Control failure due to Over speed fault in hybrid engine, Reset & manually start the engine

Trolley travelling failure due to trolley moving back a little when trolley function start. Trolley ...

Spreader function failure (lock &unlock fault) due to SR07 Spreader P#02 landing wire broken Right s ...

Control failure. Gantry Brake 01 release signal time to time Disconnect,temporry bypass

Spreader function failure (Landing Fault). Spreader P#2 landing LS Assembly loosen ,tightening & P#4 ...

Control failure. ESR36 Spreader Communication fault,SCS4 unit reset

Spreader function failure. Hybrid D1000drive Over current fault, Power reset & manually charge the B ...

Hoisting lowering failure. Snag load applied without function and reset,bypassed from hoist #01 pane ...