Equipment Breakdown Records

Spreader function failure. SR 34 spreader LHS junction box common supply Wire disconnection tight

Control failure. Engine radiator top coonent hose burst, Replaced hose & top up coolant

Spreader function failure. OHS02 Extension fault, Beam Lubricated

1. Spreader function Failure due to SQ30 spreader P#08 lock out side corner cast on bellow the ship. ...

Spreader function failure (lock &unlock fault) due to spreader 40' position signal not present, Adju ...

Control failure due to no communication with PLC, Reset the sinamics drive

Operator cabin out side gate lock handle broken. Gate lock replaced

Spreader function failure due to anti-sway cable slack, Control reset in the E. room.

Control failure due to Gantry Drive control unit communication fault,Sinamics drive control unit pow ...

Gantry traveling failure due to Near/far Failure, Replaced P#02 encoder & machine park for repaired.

Engine stop due to engine room emergency switch activated by engine door smashed because of the door ...

TROLLY LIMIT ISSUE; Operator informed that trolley stops immediately after slowdown,Synchronizing an ...

Control off due to trolley JS zero position signal missing, Joystick adjusted to get the zero positi ...

Trolley travelling fault; trolley not travelled backwards due to trolley JS reverse command not pres ...

P#4 chain replaced due to chain broken,Completed.

TLS function fault due to TLS panel door found open and rain water went through,Cleaned and blowed t ...

Spreader function failure; spreader retract fault,Retract relay replaced.

Travelling fault due to Crane to container anticollision limit activated due to 24V supply wire loos ...

Spreader function failure oil leaked due to SQ31 P#2 Lock/Unlock cylinder oil leak, Sperder was chan ...

Control failure due to MEG lockout Fault, MEG Reset and manually charge battery SOC

Gantry travelling failure due to Gantry M#1/M#2 over temperature fault/Ground fault detect Ground in ...

Spreader function failure(SQ32) due to Telescopic beam lock signal not preseted, Manually Opreted sp ...

Control on failure due to time to time Utility power voltage drop fault(PLC/Drives control supply), ...

Control failure due to Hybride System not ready/Low SOC level, Reset and Manually charge SOC level w ...

Operator compalined adjusted to trailer Limits, Adjusted to trailer limit

Spreader function failure (SKEW),No fault found from fault display.

Trolley travelling fault due to trolley over travelled, Control off and on then bypassed to re posit ...

Hoist lower fault due to emergency brake - RHS inner side down (R02) seal bolt broken,Manually opene ...

Engine stop due to low coolant level, Coolant top-up 5 L.

Anti-Sway system failure, Anti-sway pump Main contractor failed, Replaced the main contractor

Control failure, Engine over temperature signal appear ,But physical temperature is normal, Bypassed ...

Drop cable came out. Cable brought out of the headblock basket and re-assembled

Anti-sway rope fault; P#01 Antisway rope broken. Rope replaced by RRC

Hoisting lowering failure due to low hydraulic oil level from emergency brake unit. Hydraulic oil to ...

Lock Unlock Fault due to P#01 landing limit loosen. Landing limit head tighten

Hoisting lowering failure due hoist position fault. Bypassed and position recalibrated

Gantry travelling failure; Near far fault due to gantry drive motor 1 issue. Machine parked for repa ...

Gantry travelling failure due to motor drive 3 inverter fault F3001 present. Inverter fault bypassed

Lock unlock fault, After inspection, Found Spreader Unlock command wire broken ,temporally arrange ...

Control failure. Engine Stop with Hybrid not ready fault,Hybrid battary supply brakers triped,battar ...

Spreader function failure. SQ32 Spreader communication fault,tight the cable conection of spreader s ...

Spreader function failure. ESR 35 SCS 4 Stuck, Reset the SCS4

Control failure. Engine botom tank fuel empty,leval Sensor not work,manualy top up diesal(difical to ...

Engine stop due to low coolant; Coolant leak found from coolant hose mounting point, Coolant hose ti ...

Gantry travelling fault; near far not working properly,Gantry 1 chain adjusted and checked all elect ...

Spreader function failure; Side shifting not positioned back to center, Manually detected the proxim ...

travelling failure. P#2 gantry gearbox nosey, check the amp level when traveling, gear box pinion b ...

Unable to adjust the spreader to 20ft. SQ32 Stuck between 20-40,Oparate the local controll staion an ...

Spreader function failure. Head block P#2 spick motor triped off ,check the amp using clipon,reset t ...

Control failure due to hybrid battery deviation fault, Power reset from engine room.